Showing posts with label Wiring. Show all posts
Showing posts with label Wiring. Show all posts

Sunday, October 16, 2011

Wiring Up Your Spark Plugs


Your car抯 spark plug is one of the indispensable parts of your whole car. However, you are not exactly sure what it is?

A spark plug is actually an electrical device. It is found mounted into the cylinder head of an internal combustion engine. What it does is it actually ignites compressed aerosol gasoline through an electric spark. Thus, spark plugs actually are considered to be the start of a car抯 combustion. In simpler terms, your car would be able to start as long as it has spark plugs as part of its system.

Now, the electric spark that starts off from the spark plug actually is transferred to the rest of the other systems in your car with the assistance of spark plug wires. However, through time and wear, these wires could actually get brittle or could get quite rugged and old. And when this happens, your car may not run well or may not even start up even if you try to do so. Remember, automobile experts suggest that your spark plug wires should at least be changed every 30,000 miles. You can have your trusted technician do the job or you can do it yourself.

Changing spark plug wires by yourself can be quite easy. First, you should of course have new spark plug wires available. You can purchase these at auto parts stores. And when you have them ready, you should start locating the old spark plug wires that are still installed. When you have found them, pull off the wires that would be replaced. You can do this by grasping the base of the wire. You can employ a spark plug wire puller to assist you in doing the task or you can do it with just your fingers.

After you have removed the wire, check the length of the old one with the new ones you just purchased. Make sure that the new ones that you would be installing are the same length the ones that you will be replacing. And when you are sure, you can attach the new one to the spark plug. Remember that one end of the wire goes to the end of the spark plug while the other end goes to the distributor cap. You will know that it has been attached well for you will hear some sort of click or pop.



This post was made using the Auto Blogging Software from WebMagnates.org This line will not appear when posts are made after activating the software to full version.

Sunday, October 02, 2011

Car Stereo Wiring 101


I have come across a lot of car stereo systems over the past 10 years or so. There are so many "techniques" to installing head units. Everyone has their own opinion of what is right and wrong when wiring up a system, but just because it works doesn't make it right.





I asked Majestic Modifications what their opinion was on the subject. How do they install so many units and always get it right?





First, if applicable, always use the harnesses. The aftermarket wiring harness will usually take the guesswork out of the installation. These harnesses attach to the vehicle's factory wiring harness and gives you a color coded installation. You just attach red to red, yellow to yellow, etc. But is that all an installer should know?





Starting with your digital multimeter, find the power sources in the harness. One source will be continuous 12 volts, the other will be the ACC (ignition) 12 volts. These two will go with the yellow and red wires from the aftermarket head unit's harness. They are labeled accordingly. It is usually a good idea to attach the ground wire to the frame of the dash. A lot of head units come with a connector for this already attached to the ground wire. Secure these in place with some solder and shrink tubing. Slip the shrink tubing over one of the wires to be connected and move it out of the way. Connect the wires and dab a little solder on the wires. Let cool and then slide the heat shrink tubing over the connection. Heat with a heat gun/hair dryer to shrink the tubing to fit.





You can try to look on the internet for the wiring colors, but good luck. They will tell you the "typical" wire colors, but chances are it will be different. You can try two techniques to find the right wires. Clip the rest of the wires from the factory harness. You can test the speakers with a good 9 volt battery to see which speakers are which. Two wires connected to the same speaker will make it pop. Note which speaker makes the pop and attach it to that speakers wiring from the head unit. I like to turn the unit on and make sure the wires are the right polarity. A reverse wired speaker will not have as good a sound as a properly wired one. Continue the technique until all the speakers are connected.





The other way you can trace the speakers down is to turn on the head unit, but be VERY careful to not cross any wires. Start with a pair of wires, and attach them one at a time until you get sound. Note which speaker it is and attach it to that speaker's wires from the wiring harness, taking not of polarity. Continue until all the wires are in place. Zip tie the wire together and neatly tuck them behind the head unit.





Be sure you have a good ground wire connection. Be sure that RCAs or signal wires are running away from any power wires or sources, and are not run parallel to them.





If you want a neat trick, you can attach the 12 volt acc to the illumination wire, and you will be able to turn the unit on with your parking light switch. Take note, that anytime the unit is on, the dash panel lights will be on too, but you won't notice them in the daytime. The illumination wire is used to turn the factory radio lights on at night.





Not having the wiring harness for your vehicle is not a do or die situation. If you can get the harnesses, save the hassle and time and use it. If you find yourself in a bind, then follow the steps above and get it installed correctly.



This post was made using the Auto Blogging Software from WebMagnates.org This line will not appear when posts are made after activating the software to full version.